Thursday, January 16, 2014

Cách làm thuốc súng - How to Make Gunpowder


Thuốc súng hay thuốc pháo đều là chất nổ, đều dùng để làm bom.  Thuốc súng (gunpowder) còn gọi là bột đen (black powder), là một hỗn hợp gồm ba thứ:

- Potassium Nitrate (KNO3),
- Bột lưu huỳnh (sulfur S),
- Bột than (than nấu ăn giả nhỏ ra, tên tiếng Anh là Charcoal).

trộn lại.

Không biết là các bạn trong nước có gặp khó khăn khi tìm mua các vật liệu trên hay không, chứ ở Hải Ngoại thì dể mua lắm.  Nếu thấy khó khăn thì nhờ người quen ở MỸ mua giùm rồi gởi về.  Ở MỸ, những hóa chất trên có thể mua ở các cửa hàng lớn như Walmart, Home Depot, Lowes, v.v.., hay đặc mua trên mạng internet từ các công ty bán những hóa chất này.

Bây giờ, giả sử là vật liệu đã có đầy đủ rồi thì làm như thế nào?

Cách làm:


Stump remover  (Potassium Nitrate KNO3)



***

Lưu huỳnh (sulfur S)




***

Than  =  Charcoal



***

Ghi nhớ: Cả ba hóa chất này rất dễ bén lửa, nghĩa là rất dễ cháy, và cháy rất dữ dội. Do đó, khi làm phải tránh xa những chỗ có lửa, tuyệt đối không hút thuốc, hay gần những vật nóng như bàn ủi chẳng hạn. Nên đeo kiếng an toàn.

1. Dùng búa (hay cối và chày) tán nhỏ ba thứ vật liệu này ra. Ba thứ vật liệu này phải để riêng ra, không được để chung với nhau. Tán thật mịn. Rồi dùng sàn hay một miếng vải mùng để sàn lấy phần bột mịn ra.  Phần chưa mịn thì tiếp tục giả hay tán nhỏ ra, rồi lọc lấy phần bột mịn cất giữ. Xong một chất thì phải rửa búa hay chày và cối lau khô, trước khi lấy chất thứ hai ra tán. Cứ như vậy, làm hết cả ba chất nói trên.

2. Bây giờ, cẩn thận đong ba thứ bột mới vừa tán theo tỉ số sau đây:

a- Bột than = chiếm 10% của hỗn hợp = 10 gram
b- Bột lưu huỳnh = chiếm 15% của hỗn hợp. = 15 gram
c- Bột potassium nitrate (KNO3) = 75% của hỗn hợp = 75 gram.


Trong trường hợp không có cân để cân, thì bạn có thể làm theo cách sau đây:

Gọi một muỗng cafe là 5%, như vậy, bạn sẽ đong:

a- Bột than = 2 muỗng (= 10%).
b- Bột lưu huỳnh = 3 muỗng (= 15%).
c- Bột potassum nitrate = 15 muỗng (= 75%).

3. Cách trộn: 

Đổ bột than và bột lưu huỳnh chung vào nhau rồi trộn thật đều lên. Nếu có hủ nhựa có nắp thì đổ hai thứ chung vào đó, đậy nắp lại, rồi lắc. Nếu bị dính cục, thì dùng chày gỗ tán nhỏ ra, rồi lắc tiếp cho thật đều. Sau đó đổ bột potassium nitrate (KNO3) vô hủ, trộn đều, rồi đậy nắp lắc tiếp. Nếu bị đóng cục thì dùng chày gỗ tán nhỏ ra .  Như vậy là xong. Hỗn hợp bột trong hủ chính là bột đen (thuốc súng). 

Ghi chú: 

a- Có người nói là nếu thêm chừng 8% (1muỗng rưỡi) nước thì sẽ giúp tăng độ cháy. Như vậy, nếu muốn cho nước vào bột đen mà bạn mới làm xong, thì phải nhồi lên cho đều, nhồi như người ta nhồi bột làm bánh. Xong thì cất đi nếu chưa dùng tới.  Cách cất giữ tốt nhất là dùng những lon sơn đã hết.

b- Không nên pha chế nhiều cùng một lúc khi chưa quen thuộc với phương pháp này. Nên tập pha chế với số lượng nhỏ cho thật thành thạo trước khi pha chế số lượng lớn, để tránh nguy hiểm nếu có gì xãy ra.





Gunpowder


*********************************************************************************

Gunpowder, also called black powder, is a simple mixture of saltpeter, sulfur, and charcoal. The trickiest part of making black powder is sourcing these three supplies. Once you find them, you mix them together and create an explosive black meal. Be extremely cautious when handling black powder, and make sure to store it away from heat and flame. Read on to learn more about how to make gunpowder.


Part 1 of 2: Collecting the Ingredients

1. Get your hands on some saltpeter. Saltpeter is the common name for potassium nitrate (KNO3). In the days when black powder was widely used, saltpeter was manufactured from bat guano or made from horse urine and other "manurial soils."[1] It's used in many fertilizers, as part of science projects, and in certain recipes. You have several options for sourcing saltpeter:

Look for "stump remover" in garden stores. Saltpeter is often sold under this name. You may also find it labeled as saltpeter, niter, or potassium nitrate.[2]

Buy it online. If you do a search for saltpeter, you'll get plenty of results, and you can easily have a bottle delivered to you.

Make it yourself out of a cold pack. Cold packs you can buy for a few dollars to help with sore muscles contain sodium nitrate and water, and can be used to make saltpeter.

Make it with urine. This is definitely the most difficult way to source saltpeter, but some black powder enthusiasts prefer to make their powder entirely from scratch. To do so, one process is to fill a drum with manure affixed with a drain, valve, and filter at the bottom. Urinate into it, then top it off with water. After about 10 months, dry it out on trays.[3]

2. Obtain charcoal. 

You can use standard charcoal that you buy to cook with your grill, which you'll need to grind to a fine powder. If you're a purist, make your own charcoal by filling a metal drum with 3-inch pieces of willow or another wood, then placing the drum in a bonfire with a loose lid on top (to allow for airflow). Keep the bonfire piping hot for 4-6 hours, then open the drum. The wood will have charred into fine pieces of homemade charcoal, perfect for use in gunpowder.

3. Get elemental sulfur. 

This naturally-occurring substance is often used to acidify soil, so you can find it in garden stores or from online sources that sell garden supplies. Elemental sulfur occurs naturally and is mined from beds in Texas, Louisiana, Italy, and other locations around the world.[4]

Part 2 of 2: Mixing the Ingredients

1. Finely grind the ingredients. 

Use a mortar and pestle to grind each ingredient into a fine powder. Grind each ingredient separately, cleaning the mortar and pestle in between uses.

You can use a ball mill to grind the components if you're planning on making a lot of gunpowder. A ball mill is used to both grind and mix powders safely.

2. Measure out the gunpowder components. 

Using the right ration of ingredients is very important when you're making gunpowder. Calculate the percentages by weight, using a small scale to weigh the different ingredients. Here's how much you need:

75% saltpeter (5 parts)

15% charcoal (1 part)

10% sulfur (2/3 of 1 part)



3. Mix the ingredients together:
Place them all in the mortar and grind them together with the pestle for 10 minutes or longer. If you're using a ball mill, mill the charcoal and sufur together for 4 hours first, then add the saltpeter and mill the mixture for another 24 hours.

Be extremely careful around the black powder once it has been mixed. Do not smoke or light a flame anywhere close to the powder, and keep it away from heat.



4. Consider adding water. 
Some say adding up to 8% water can improve the gunpowder's burning. Continue mixing the gunpowder, adding water in small increments until the gunpowder is the texture of thick clay. Form it into a ball when you're finished.

If you mix the gunpowder with water, you'll need to corn the gunpowder, or break it up into small pieces. Run the gunpowder ball through a kitchen sieve to break it into small pieces, then let the pieces dry out on a piece of paper.[5]

Again, be extremely careful around the gunpowder. Exercise caution at every stage.

5. Store the black powder safely. 
Place the black powder in a special container designed for gunpowder. Consider storing it in a fireproof box in a shed or another area outside your home. In any case, store the black powder in a stable area where it will not come into contact with a flame or be exposed to high temperatures.

You can buy powder containers at hardware stores or online.

Some recommend using empty (unused) paint cans to store black powder.

http://www.wikihow.com/Make-Gunpowder





*************************************************************************

Cách làm thuốc súng

Thuốc súng hay thuốc pháo đều là chất nổ, đều dùng để làm bom.Thuốc súng (gunpowder) còn gọi là bột đen (black powder), là một hỗn hợp gồm ba thứ:

- potassium nitrate (KNO3),
- bột lưu huỳnh(sulfur S),
- bột than (than nấu ăn giả nhỏ ra, tên tiếng Anh là Charcoal)

trộn lại.

Không biết là các bạn trong nước có gặp khó khăn khi tìm mua các vật liệu trên hay không, chứ ở Hải Ngoại thì dể mua lắm.  Nếu thấy khó khăn thì nhờ người quen ở MỸ mua giùm rồi gởi về.  Ở MỸ, những hóa chất trên có thể mua ở các cửa hàng lớn như Walmart, Home Depot, Lowes, v.v.., hay đặc mua trên mạng internet từ các công ty bán những hóa chất này.

Bây giờ, giả sử là vật liệu đã có đầy đủ rồi thì làm như thế nào?

Cách làm:

Ghi nhớ: Cả ba hóa chất này rất dễ bén lửa, nghĩa là rất dễ cháy, và cháy rất dữ dội. Do đó, khi làm phải tránh xa những chỗ có lửa, tuyệt đối không hút thuốc, hay gần những vật nóng như bàn ủi chẳng hạn. Nên đeo kiếng an toàn.

1. Dùng búa (hay cối và chày) tán nhỏ ba thứ vật liệu này ra. Ba thứ vật liệu này phải để riêng ra, không được để chung với nhau. Tán thật mịn. Rồi dùng sàn hay một miếng vải mùng để sàn lấy phần bột mịn ra.  Phần chưa mịn thì tiếp tục giả hay tán nhỏ ra, rồi lọc lấy phần bột mịn cất giữ. Xong một chất thì phải rửa búa hay chày và cối lau khô, trước khi lấy chất thứ hai ra tán. Cứ như vậy, làm hết cả ba chất nói trên.

2. Bây giờ, cẩn thận đong ba thứ bột mới vừa tán theo tỉ số sau đây:

a- Bột than = chiếm 10% của hỗn hợp = 10 gram
b- Bột lưu huỳnh = chiếm 15% của hỗn hợp. = 15 gram
c- Bột potassium nitrate (KNO3) = 75% của hỗn hợp = 75 gram.

Trong trường hợp không có cân để cân, thì bạn có thể làm theo cách sau đây:

Gọi một muỗng cafe là 5%, như vậy, bạn sẽ đong:

a- Bột than = 2 muỗng (= 10%).
b- Bột lưu huỳnh = 3 muỗng (= 15%).
c- Bột potassum nitrate = 15 muỗng (= 75%).

3. Cách trộn: 

Đổ bột than và bột lưu huỳnh chung vào nhau rồi trộn thật đều lên. Nếu có hủ nhựa có nắp thì đổ hai thứ chung vào đó, đậy nắp lại, rồi lắc. Nếu bị dính cục, thì dùng chày gỗ tán nhỏ ra, rồi lắc tiếp cho thật đều. Sau đó đổ bột potassium nitrate (KNO3) vô hủ, trộn đều, rồi đậy nắp lắc tiếp. Nếu bị đóng cục thì dùng chày gỗ tán nhỏ ra .  Như vậy là xong. Hỗn hợp bột trong hủ chính là bột đen (thuốc súng). 

Ghi chú: 

a- Có người nói là nếu thêm chừng 8% (1muỗng rưỡi) nước thì sẽ giúp tăng độ cháy. Như vậy, nếu muốn cho nước vào bột đen mà bạn mới làm xong, thì phải nhồi lên cho đều, nhồi như người ta nhồi bột làm bánh. Xong thì cất đi nếu chưa dùng tới.  Cách cất giữ tốt nhất là dùng những lon sơn đã hết.

b- Không nên pha chế nhiều cùng một lúc khi chưa quen thuộc với phương pháp này. Nên tập pha chế với số lượng nhỏ cho thật thành thạo trước khi pha chế số lượng lớn, để tránh nguy hiểm nếu có gì xãy ra.

1 comment:

  1. Cho mình hỏi cái stump remover ấy nó là cái gì vậy???

    ReplyDelete